3.2.2.3.9.5.1. Project - v0.94

Red Pitaya HDL design has multiple functions, which are configured by registers. It also uses memory locations to store capture data and generate output signals. All of these are described in this document. The memory location is written in a way that is seen by SW.

The table describes address space partitioning implemented on FPGA via the AXI GP0 interface. All registers have offsets aligned to 4 bytes and are 32-bit wide. Granularity is 32-bit, meaning that the minimum transfer size is 4 bytes. The organization is a little-endian. The memory block is divided into 8 parts. Each part is occupied by an individual IP core. The address space of individual applications is described in the subsection below. The size of each IP core address space is 4MByte. For additional information and better understanding check other documents (schematics, specifications…).

Start

End

Module Name

CS[0]

0x40000000

0x400FFFFF

Housekeeping

CS[1]

0x40100000

0x401FFFFF

Oscilloscope

CS[2]

0x40200000

0x402FFFFF

Arbitrary signal generator (ASG) 125-14-4ADC: Oscilloscope CHC and CHD

CS[3]

0x40300000

0x403FFFFF

PID controller

CS[4]

0x40400000

0x404FFFFF

Analog mixed signals (AMS)

CS[5]

0x40500000

0x405FFFFF

Daisy chain

CS[6]

0x40600000

0x406FFFFF

FREE

CS[7]

0x40700000

0x407FFFFF

Power test

3.2.2.3.9.5.1.1. Housekeeping

offset

description

bits

R/W

0x0

ID

Reserved

31:4

R

Design ID

3:0

R

0 -prototype

1 -release

0x4

DNA part 1

DNA[31:0]

31:0

R

0x8

DNA part 2

Reserved

31:25

R

DNA[56:32]

24:0

R

0xC

Digital Loopback

Reserved

31:1

R

digital_loop

0

R/W

0x10

Expansion connector direction P

Reserved

31:8

R

Direction for P lines

7:0

R/W

1-out

0-in

0x14

Expansion connector direction N

Reserved

31:8

R

Direction for N lines

7:0

R/W

1-out

0-in

0x18

Expansion connector output P

Reserved

31:8

R

P pins output

7:0

R/W

0x1C

Expansion connector output N

Reserved

31:8

R

N pins output

7:0

R/W

0x20

Expansion connector input P

Reserved

31:8

R

P pins input

7:0

R

0x24

Expansion connector input N

Reserved

31:8

R

N pins input

7:0

R

0x30

LED control

Reserved

31:8

R

LEDs 7-0

7:0

R/W

0x34

CAN0 pins enable

Reserved

31:1

R

Enable CAN0 - 1

0

R/W

CAN0_rx: GPIO_P 7 ; CAN1_rx : GPIO_P 6

CAN0_tx: GPIO_N 7 ; CAN1_tx : GPIO_N 6

0x100

FPGA ready

Reserved

31:1

R

Programmable logic is out of reset

0

R

0x1000

External trigger override

Reserved

31:3

R

Trigger output selector 1: DAC trigger, 0: ADC trigger

2

R/W

Override GPIO_N_0 to output ADC or DAC trigger

1

R/W

Enable sending and receiving external trigger through daisy chain connectors 1: enable, 0: disable

0

R/W

3.2.2.3.9.5.1.2. Oscilloscope

Note

For STEMlab 125-14 4-Input register writes are duplicated for channels A/B and C/D. The output registers are replaced with a mirrored version of the input registers for channels C/D (IN3/IN4).

offset

description

bits

R/W

0x0

Configuration *

Reserved

31:5

R

ACQ delay has passed / (all data was written to buffer)

4

R

Trigger remains armed after ACQ delay passes

3

W

Trigger has arrived stays on (1) until next arm or reset

2

R

Reset write state machine

1

W

Start writing data into memory (ARM trigger).

0

W

0x4

Trigger source *

Selects trigger source for data capture. When trigger delay is ended value goes to 0.

Reserved

31:4

R
Trigger source
1 - trig immediately
2 - ch A threshold positive edge
3 - ch A threshold negative edge
4 - ch B threshold positive edge
5 - ch B threshold negative edge
6 - external trigger positive edge - DIO0_P pin
7 - external trigger negative edge
8 - arbitrary wave generator application positive edge
9 - arbitrary wave generator application negative edge
10- ch C threshold positive edge
11- ch C threshold negative edge
12- ch D threshold positive edge
13- ch D threshold negative edge

3:0

R/W

0x8

Ch A threshold

Reserved

31:14

R

Ch A threshold, makes trigger when ADC value cross this value

13:0

R/W

0xC

Ch B threshold

Reserved

31:14

R

Ch B threshold, makes trigger when ADC value cross this value

13:0

R/W

0x10

Delay after trigger *

Number of decimated data after trigger written into memory

31:0

R/W

0x14

Data decimation *

Decimate input data, uses data average

Reserved

31:17

R

Data decimation: Values 1, 2, 4, 8 are supported for values less than 16. Above 16, averaging of any number of samples is supported.

16:0

R/W

0x18

Write pointer - current

Reserved

31:14

R

Current write pointer

13:0

R

0x1C

Write pointer - trigger

Reserved

31:14

R

Write pointer at time when trigger arrived

13:0

R

0x20

Ch A hysteresis

Reserved

31:14

R

Ch A threshold hysteresis. Value must be outside to enable trigger again.

13:0

R/W

0x24

Ch B hysteresis

Reserved

31:14

R

Ch B threshold hysteresis. Value must be outside to enable trigger again.

13:0

R/W

0x28

Other

Reserved Enable signal average at decimation

31:1 0

R R/W

0x2C

PreTrigger Counter

This unsigned counter holds the number of samples captured between the start of acquire and trigger. The value does not overflow, instead it stops incrementing at 0xffffffff.

31:0

R

0x30

CH A Equalization filter

Reserved

31:18

R

AA Coefficient

17:0

R/W

0x34

CH A Equalization filter

Reserved

31:25

R

BB Coefficient

24:0

R/W

0x38

CH A Equalization filter

Reserved

31:25

R

KK Coefficient

24:0

R/W

0x3C

CH A Equalization filter

Reserved

31:25

R

PP Coefficient

24:0

R/W

0x40

CH B Equalization filter

Reserved

31:18

R

AA Coefficient

17:0

R/W

0x44

CH B Equalization filter

Reserved

31:25

R

BB Coefficient

24:0

R/W

0x48

CH B Equalization filter

Reserved

31:25

R

KK Coefficient

24:0

R/W

0x4C

CH B Equalization filter

Reserved

31:25

R

PP Coefficient

24:0

R/W

0x50

CH A AXI lower address

Starting writing address

31:0

R/W

0x54

CH A AXI upper address

Address where it jumps to lower

31:0

R/W

0x58

CH A AXI delay after trigger

Number of decimated data after trigger written into memory

31:0

R/W

0x5C

CH A AXI enable master

Reserved

31:1

R

Enable AXI master

0

R/W

0x60

CH A AXI write pointer - trigger

Write pointer at time when trigger arrived

31:0

R

0x64

CH A AXI write pointer - current

Current write pointer

31:0

R

0x70

CH B AXI lower address

Starting writing address

31:0

R/W

0x74

CH B AXI upper address

Address where it jumps to lower

31:0

R/W

0x78

CH B AXI delay after trigger

Number of decimated data after trigger written into memory

31:0

R/W

0x7C

CH B AXI enable master

Reserved

31:1

R

Enable AXI master

0

R/W

0x80

CH B AXI write pointer - trigger

Write pointer at time when trigger arrived

31:0

R

0x84

CH B AXI write pointer - current

Current write pointer

31:0

R

0x88

AXI state registers

Reserved

31:21

R

CH B AXI - ACQ delay has passed / (all data was written to buffer)

20

R

CH B AXI - Trigger remains armed / after ACQ delay passes

19

R

CH B AXI - Trigger has arrived stays on (1) until next arm or reset

18

R

Reserved

17

R

CH A AXI - Trigger armed

16

R

Reserved

15:5

R

CH A AXI - ACQ delay has passed / (all data was written to buffer)

4

R

CH A AXI - Trigger remains armed / after ACQ delay passes

3

R

CH A AXI - Trigger has arrived stays on (1) until next arm or reset

2

R

Reserved

1

R

CH A AXI - Trigger armed

0

R

0x90

Trigger debouncer time

Number of ADC clock periods trigger is disabled after activation reset value is decimal 62500 or equivalent to 0.5ms

19:0

R/W

0xA0

Accumulator data sequence length

Reserved

31:14

R

0xA4

Accumulator data offset corection ChA

Reserved

31:14

R

signed offset value

13:0

R/W

0xA8

Accumulator data offset corection ChB

Reserved

31:14

R

signed offset value

13:0

R/W

0x10000 to 0x1FFFC

Memory data (16k samples)

Reserved

31:16

R

Captured data for ch A

15:0

R

0x20000 to 0x2FFFC

Memory data (16k samples)

Reserved

31:16

R

Captured data for ch B

15:0

R

3.2.2.3.9.5.1.3. Arbitrary Signal Generator (ASG)

Note

Oscilloscope CHC and CHD (125-14 4-Input)

Register writes synchronised between channels A/B and C/D on 4 input board 125-14 4-Input The output registers are replaced with a mirrored version of the input registers for channels C/D (IN3/IN4).

offset

description

bits

R/W

0x0

Configuration

Reserved

31:25

R

ch B external gated repetitions

24

R/W

ch B set output to 0

23

R/W

ch B SM reset

22

R/W

Reserved

21

R/W

ch B SM wrap pointer (if disabled starts at address0 )

20

R/W
ch B trigger selector: (don’t change when SM is
active)
1-trig immediately
2-external trigger positive edge - DIO0_P pin
3-external trigger negative edge

19:16

R/W

Reserved

15:9

R

ch A external gated bursts

8

R/W

ch A set output to 0

7

R/W

ch A SM reset

6

R/W

Reserved

5

R/W

ch A SM wrap pointer (if disabled starts at address 0)

4

R/W
ch A trigger selector: (don’t change when SM is
active)
1-trig immediately
2-external trigger positive edge - DIO0_P pin
3-external trigger negative edge

3:0

R/W

0x4

Ch A amplitude scale and offset

out = (data*scale)/0x2000 + offset

Reserved

31:30

R

Amplitude offset

29:16

R/W

Reserved

15:14

R

Amplitude scale. 0x2000 == multiply by 1. Unsigned

13:0

R/W

0x8

Ch A counter wrap

Reserved

31:30

R

Value where counter wraps around. Depends on SM wrap setting. If it is 1 new value is get by wrap, if value is 0 counter goes to offset value. 16 bits for decimals.

29:0

R/W

0xC

Ch A start offset

Reserved

31:30

R

Counter start offset. Start offset when trigger arrives. 16 bits for decimals.

29:0

R/W

0x10

Ch A counter step

Reserved

31:30

R

Counter step. 16 bits for decimals.

29:0

R/W

0x14

Ch A counter step- lower bits

Counter step read

31:0

R

0x18

Ch A number of read cycles in one burst

Reserved

31:16

R

Number of repeats of table readout. 0=infinite

15:0

R/W

0x1C

Ch A number of burst repetitions

Reserved

31:16

R

Number of repetitions. 0=disabled 0xffff=infinite

15:0

R/W

0x20

Ch A delay between burst repetitions

Delay between repetitions. Granularity=1us

31:0

R/W

0x24

Ch B amplitude scale and offset

out = (data*scale)/0x2000 + offset

Reserved

31:30

R

Amplitude offset

29:16

R/W

Reserved

15:14

R

Amplitude scale. 0x2000 == multiply by 1. Unsigned

13:0

R/W

0x28

Ch B counter wrap

Reserved

31:30

R

Value where counter wraps around. Depends on SM wrap setting. If it is 1 new value is get by wrap, if value is 0 counter goes to offset value. 16 bits for decimals.

29:0

R/W

0x2C

Ch B start offset

Reserved

31:30

R

Counter start offset. Start offset when trigger arrives. 16 bits for decimals.

29:0

R/W

0x30

Ch B counter step

Reserved

31:30

R

Counter step. 16 bits for decimals.

29:0

R/W

0x34

Ch B counter step- lower bits

Counter step read

31:0

R

0x38

Ch B number of read cycles in one burst

Reserved

31:16

R

Number of repeats of table readout. 0=infinite

15:0

R/W

0x3C

Ch B number of burst repetitions

Reserved

31:16

R

Number of repetitions. 0=disabled 0xffff=infinite

15:0

R/W

0x40

Ch B delay between burst repetitions

Delay between repetitions. Granularity=1us

31:0

R/W

0x44

Ch A value of last sample in burst

Reserved

31:14

R

Last value of burst

13:0

R/W

0x48

Ch B value of last sample in burst

Reserved

31:14

R

Last value of burst

13:0

R/W

0x4C

Ch A counter step- lower bits

Counter step write

31:0

W

0x50

Ch B counter step- lower bits

Counter step write

31:0

W

0x54

External trigger debouncer

Number of ADC clock periods trigger is disabled after activation. Default value is decimal 62500 or equivalent to 0.5ms

19:0

R/W

0x60

Ch A buffer current read pointer

Reserved

31:16

R

Read pointer

15:2

R/W

Reserved

1:0

R

0x64

Ch B buffer current read pointer

Reserved

31:16

R

Read pointer

15:2

R/W

Reserved

1:0

R

0x68

Ch A initial value of generator

Reserved

31:14

R

First value

13:0

R/W

0x6C

Ch B initial value of generator

Reserved

31:14

R

First value

13:0

R/W

0x10000 to 0x1FFFC

Ch A memory data (16k samples)

Reserved

31:14

R

ch A data

13:0

R/W

0x20000 to 0x2FFFC

Ch B memory data (16k samples)

Reserved

31:14

R

ch B data

13:0

R/W

3.2.2.3.9.5.1.4. PID Controller

offset

description

bits

R/W

0x0

Configuration

Reserved

31:4

R

PID22 integrator reset

3

R/W

PID21 integrator reset

2

R/W

PID12 integrator reset

1

R/W

PID11 integrator reset

0

R/W

0x10

PID11 set point

Reserved

31:14

R

PID11 set point

13:0

R/W

0x14

PID11 proportional coefficient

Reserved

31:14

R

PID11 Kp

13:0

R/W

0x18

PID11 integral coefficient

Reserved

31:14

R

PID11 Ki

13:0

R/W

0x1C

PID11 derivative coefficient

Reserved

31:14

R

PID11 Kd

13:0

R/W

0x20

PID12 set point

Reserved

31:14

R

PID12 set point

13:0

R/W

0x24

PID12 proportional coefficient

Reserved

31:14

R

PID12 Kp

13:0

R/W

0x28

PID12 integral coefficient

Reserved

31:14

R

PID12 Ki

13:0

R/W

0x2C

PID12 derivative coefficient

Reserved

31:14

R

PID12 Kd

13:0

R/W

0x30

PID21 set point

Reserved

31:14

R

PID21 set point

13:0

R/W

0x34

PID21 proportional coefficient

Reserved

31:14

R

PID21 Kp

13:0

R/W

0x38

PID21 integral coefficient

Reserved

31:14

R

PID21 Ki

13:0

R/W

0x3C

PID21 derivative coefficient

Reserved

31:14

R

PID21 Kd

13:0

R/W

0x40

PID22 set point

Reserved

31:14

R

PID22 set point

13:0

R/W

0x44

PID22 proportional coefficient

Reserved

31:14

R

PID22 Kp

13:0

R/W

0x48

PID22 integral coefficient

Reserved

31:14

R

PID22 Ki

13:0

R/W

0x4C

PID22 derivative coefficient

Reserved

31:14

R

PID22 Kd

13:0

R/W

3.2.2.3.9.5.1.5. Analog Mixed Signals (AMS)

offset

description

bits

R/W

0x0

XADC AIF0 (disabled)

Reserved

31:12

R

AIF0 value

11:0

R

0x4

XADC AIF1 (disabled)

Reserved

31:12

R

AIF1 value

11:0

R

0x8

XADC AIF2 (disabled)

Reserved

31:12

R

AIF2 value

11:0

R

0xC

XADC AIF3 (disabled)

Reserved

31:12

R

AIF3 value

11:0

R

0x10

XADC AIF4 (disabled)

Reserved

31:12

R

AIF4 value (5V power supply)

11:0

R

0x20

PWM DAC0

Reserved

31:24

R

PWM value (100% == 255)

23:16

R/W

Bit select for PWM repetition which have value PWM+1

15:0

R/W

0x24

PWM DAC1

Reserved

31:24

R

PWM value (100% == 255)

23:16

R/W

Bit select for PWM repetition which have value PWM+1

15:0

R/W

0x28

PWM DAC2

Reserved

31:24

R

PWM value (100% == 255)

23:16

R/W

Bit select for PWM repetition which have value PWM+1

15:0

R/W

0x2C

PWM DAC3

Reserved

31:24

R

PWM value (100% == 255)

23:16

R/W

Bit select for PWM repetition which have value PWM+1

15:0

R/W

3.2.2.3.9.5.1.6. Daisy Chain

offset

description

bits

R/W

0x0

Control

Reserved

31:2

R

RX enable

1

R/W

TX enable

0

R/W

0x4

Transmitter data selector

Custom data

31:1

R/W

Reserved

15:8

R
Data source
0 - data is 0
1 - user data (from logic)
2 - custom data (from this register)
3 - training data (0x00FF)
4 - transmit received data (loop back)
5 - random data (for testing)

3:0

R/W

0x8

Receiver training

Reserved

31:2

R

Training successful

1

R

Enable training

0

R/W

0xC

Received data

Received data which is different than 0

31:1

R

Received raw data

15:0

R

0x10

Testing control

Reserved

31:1

R

Reset testing counters (error & data)

0

R/W

0x14

Testing error counter

Error increases if received data is not the same as transmitted testing data

31:0

R

0x18

Testing data counter

Counter increases when value different as 0 is received

31:0

R

3.2.2.3.9.5.1.7. Power Test

offset

description

bits

R/W

0x0

Control

Reserved

31:1

R

Enable module

0

R/W